1980 Mercury Bobcat Recommended Tire Pressure

Recommended tire inflation pressures for 1980 Mercury Bobcat tires to improve fuel efficiency, extend tire life and drive safely.

Recommended tire pressure for 1980 Mercury Bobcat ranges around 24 psi for front tires and 24 to 30 psi for rear tires. Select your trim to see original equipment tire sizes and recommended tire inflation pressures.

1980 Mercury Bobcat Base Model Tire Pressure

Recommended tire pressure for 1980 Mercury Bobcat Base Model tires (1 original equipment tire size set).

Front and Rear Tire Size 175/80R13
Recommended Front Tire Pressure 24 psi (1.7 bar or 165 kPa)
Recommended Rear Tire Pressure 30 psi (2.1 bar or 207 kPa)
Tire Size Type Metric
Tire Load Index
Tire Load Capacity
Tire Speed Rating
Maximum Tire Speed
Tire Load Range SL (Standard Load)
Maximum Load Tire Pressure 36 psi

1980 Mercury Bobcat Runabout Tire Pressure

Recommended tire pressure for 1980 Mercury Bobcat Runabout tires (1 original equipment tire size set).

Front and Rear Tire Size 175/80R13
Recommended Front Tire Pressure 24 psi (1.7 bar or 165 kPa)
Recommended Rear Tire Pressure 24 psi (1.7 bar or 165 kPa)
Tire Size Type Metric
Tire Load Index
Tire Load Capacity
Tire Speed Rating
Maximum Tire Speed
Tire Load Range SL (Standard Load)
Maximum Load Tire Pressure 36 psi

1980 Mercury Bobcat Villager Tire Pressure

Recommended tire pressure for 1980 Mercury Bobcat Villager tires (1 original equipment tire size set).

Front and Rear Tire Size 175/80R13
Recommended Front Tire Pressure 24 psi (1.7 bar or 165 kPa)
Recommended Rear Tire Pressure 30 psi (2.1 bar or 207 kPa)
Tire Size Type Metric
Tire Load Index
Tire Load Capacity
Tire Speed Rating
Maximum Tire Speed
Tire Load Range SL (Standard Load)
Maximum Load Tire Pressure 36 psi

All tire pressure information listed is for informational purposes only. TirePressure.com does not warrant or make any representations regarding the use of or the results of the use of this information. Always refer to your vehicle owner's manual for proper tire inflation pressures.

Mercury Tire Pressure | Mercury Bobcat Tire Pressure | 1980 Mercury Tire Pressure

It is vital to maintain proper tire inflation pressures for 1980 Mercury Bobcat tires. Low tire pressure will result in tire underinflation while high tire pressure will result in tire overinflation, which can decrease fuel efficiency, lead to uneven tire tread wear and reduce tire life, compromise tire safety and cause tire blowout. Check 1980 Mercury Bobcat tire pressure regularly, and monitor 1980 Mercury Bobcat tire inflation pressures to avoid driving with overinflated or underinflated tires.

Tire inflation listed on tire sidewall is the maximum air pressure the tire can hold to carry its maximum load, and not the recommended tire pressure for 1980 Mercury Bobcat. Use 1980 Mercury Bobcat recommended tire pressure settings listed on the tire pressure chart found in 1980 Mercury Bobcat owner's manual, on a tire placard on driver's door or door jam, inner trunk lid, in the console or on the fuel door. Recommended tire pressure for your 1980 Mercury Bobcat tire sizes will be listed in one of the following pressure units: psi (pounds per square inch), bar or kPa (kiloPascals). Pay attention as your 1980 Mercury Bobcat may have different recommended tire inflation pressures for front and rear tires, especially if equipped with staggered tires. Keep your 1980 Mercury Bobcat tires inflated at recommended tire inflation pressures at all times for your driving comfort and safety.

If you replace 1980 Mercury Bobcat original equipment tires or switch to plus size tires, make sure to follow guidelines for the application of load and inflation tables to find proper tire pressure for your new 1980 Mercury Bobcat tires. 1980 Mercury Bobcat tires with the same load index, regardless of tire size, may carry the same load, but may require substantially different inflation pressures. Tire load index may not be used independently to determine replacement tire acceptability for load capacity. An equal or greater load index does not always correspond to equal or greater load capacity at all inflation pressure settings. 1980 Mercury Bobcat replacement tires must have equal or greater speed rating compared to the original equipment tires if your 1980 Mercury Bobcat speed capability is to be maintained. It is recommended that tire installers refer to the 1980 Mercury Bobcat owner’s manual to identify any tire speed rating restriction or recommendation that could affect the operation of the vehicle. If your 1980 Mercury Bobcat replacement tires have a lower speed rating than the original equipment tires, your vehicle’s speed must be restricted to that of the replacement tires. Original equipment tires that come on your 1980 Mercury Bobcat will have the proper tire load index, so use same or higher load index when choosing replacement tires. Tire load index tells you how much weight your tire can carry. Putting too much weight on your tires will overload them, and can cause premature tire wear, tire damage or even tire blowout. Refer to your 1980 Mercury Bobcat manual to find its original equipment tire sizes and load ratings. Always refer to the 1980 Mercury Bobcat owner’s manual for any specific safety advice regarding the application of 1980 Mercury Bobcat replacement tires.

1980 Mercury Bobcat tire pressure may fluctuate with ambient temperatures, so check 1980 Mercury Bobcat tire pressure when ambient temperatures change. In winter when temperatures drop, 1980 Mercury Bobcat tires may deflate by approximately 1 psi for each 10 degree Fahrenheit decrease in temperature. Maintain proper 1980 Mercury Bobcat winter tire pressure by adding air to your tires as needed to the recommended tire inflation levels.

1980 Mercury Bobcat tire pressure should be checked when tires are cold, after your vehicle has not been driven for at least three hours. It is best to check your tire inflation pressure in the morning, after the vehicle has been parked overnight, using a reliable tire pressure gauge.

If your 1980 Mercury Bobcat is equipped with tire pressure monitoring system (TPMS), pay attention to low tire pressure warning light being on. Ensure 1980 Mercury Bobcat tire pressure sensors are working properly to stay alert and enjoy a safe ride. If your tire pressure warning light is on, check front and rear tires to make sure they are properly inflated.

What is the recommended tire pressure for 1980 Mercury Bobcat?
Recommended tire pressure for 1980 Mercury Bobcat is determined by the manufacturer based on your vehicle's characteristics and original equipment tire sizes. Select your 1980 Mercury Bobcat trim to get recommended tire inflation pressures for 1980 Mercury Bobcat tires.

Where do I find recommended tire pressure settings for 1980 Mercury Bobcat?
You can find your 1980 Mercury Bobcat recommended tire pressure in 1980 Mercury Bobcat owner's manual, on a tire placard on driver's door or door jam, inner trunk lid, in the console or on the fuel door. Recommended tire pressure for 1980 Mercury Bobcat will be listed in psi, bar or kPa.

How to check 1980 Mercury Bobcat tire pressure?
Proper 1980 Mercury Bobcat tire inflation is essential to the overall tire performance and safety. To check tire pressure for 1980 Mercury Bobcat you will need to know its recommended tire pressure and a tire pressure gauge. Check cold inflation pressures in 1980 Mercury Bobcat tires with tire pressure gauge and adjust to 1980 Mercury Bobcat recommended tire inflation pressures as needed by adding or releasing air. Make sure to check tire inflation for your 1980 Mercury Bobcat regularly to ensure safe and comfortable drive.

Why is 1980 Mercury Bobcat tire pressure warning light on?
If your 1980 Mercury Bobcat is equipped with Tire Pressure Monitoring System (TPMS) it will alert you when tire pressure is too low and your tires could be underinflated, which can lead to uneven tire wear or can cause tire failure. If 1980 Mercury Bobcat low tire pressure warning light is on, check all 1980 Mercury Bobcat tires for low air pressure and inflate tires to the recommended tire inflation pressures. Keep in mind that Tire Pressure Monitoring System does not replace routine tire pressure check and maintenance.

How do I reset 1980 Mercury Bobcat tire pressure monitoring system?
To reset tire pressure monitoring system for 1980 Mercury Bobcat, make sure front and rear tires are inflated to the recommended levels. Refer to your owner's manual on how to reset 1980 Mercury Bobcat TPMS.

What is recommended winter tire pressure for 1980 Mercury Bobcat?
Recommended tire pressure for 1980 Mercury Bobcat is the same for any season, but you may inflate your 1980 Mercury Bobcat tires 3 to 5 psi above the recommended tire pressure set by the manufacturer to compensate for lower temperatures during winter. Make sure to check your 1980 Mercury Bobcat tire pressure more often in the winter to keep tires properly inflated for a safe ride on snow and icy roads.

Tire Pressure Guide